Removal of tetracycline by ultraviolet/sodium percarbonate (UV/SPC)advanced oxidation process in water.

Tetracycline (TC) was widely used and frequently detected in various water bodies, where the presence of TC posed a significant threat to the health of aquatic organisms. Furthermore, antibiotics were hardly degraded by biological treatment. Thus, in order to enhance the removal of TC, we proposed the use of a novel ultraviolet/sodium percarbonate (UV/SPC) advanced oxidation process and initiated an in-depth study. The study investigated the influence of oxidant dosage, initial pH, UV intensity, and TC concentration on the removal of TC. The results demonstrated that the UV/SPC system efficiently removed TC, with removal efficiency increasing as the SPC concentration increased. Within the pH range of 3-11, TC degradation exhibited minimal variation, indicating the UV/SPC system's strong adaptability to pH variations. The research on the impact of the water matrix on TC removal revealed that HCO3- had an inhibitory effect on TC degradation, while NO3- promoted TC degradation. Additionally, the presence of free radical species (·OH, ·CO3-, ·O2-) were detected and rate constants for the secondary reactions (k·OH,TC = 6.3 × 109 L mol-1·s-1, k·CO3-,TC = 3.4 × 108 L mol-1·s-1) were calculated, indicating that ·OH exhibited a stronger oxidative performance compared to ·CO3-. This study did not only present a novel strategy via UV/SPC to remove TC but also uncovered the unique role of ·CO3- for contaminant removal.

Insight into characteristics of sulphur-based autotrophic denitrifying microbiota in the nitrate removal.

Mariculture wastewater is characterized by low organic carbon to nitrogen ratio (C/N) but high nitrate concentration, which makes it difficult to remove nitrate by the completely heterotrophic denitrification. However, high nitrate discharge poses a threat to the natural environment and human health. Thus, we enriched sulphur-based autotrophic denitrifying (SAD) microbiota and optimized the nitrate removal under different environmental factors and electron donor conditions. The results showed that the dominant genera in the enriched microbiota were previously confirmed autotrophic denitrifiers, Sulfurovum, Thioalkalispira-Sulfurivermis, and Sedimenticola, with a high relative abundance of 41.14%, 21.01%, and 6.17%. Among the environmental factors, pH was the key factor affecting SAD microbiota, and pH 7-9 favoured nitrate removal. However, high pH led to nitrite accumulation (e.g. 10 mg/L at pH = 9), which should be strictly avoided. With regard to electron donors, the optimal concentrations of thiosulphate and nitrate were 50 and 5 mg/L, respectively. The best organic carbon is acetate with an optimal concentration of 10 mg/L. Meanwhile, the initial concentration of thiosulphate was proportional to the nitrate removal rate, while higher concentrations of organic carbon stimulated the heterotrophic denitrification potential of microbiota and thus benefited to dentrification. This study showed that the enriched SAD microbiota was able to achieve efficient nitrate removal under suitable environmental conditions and mixed electron donors and thus presented the potential for application in the treatment of mariculture wastewater.

Anode modification of sediment microbial fuel cells (SMFC) towards bioremediating mariculture wastewater.

Remediation of mariculture wastewater is of great practical importance. In this study, sediment microbial fuel cells (SMFCs) were adopted and carbon felt anodes were modified to enhance COD and ammonia removal in mariculture system. The results showed that the SMFC anode with 5 % (w/w) graphene oxide (GO) coating performed best in pollutants removal and electricity generation. The maximum power density approached 132 mW/m2, nearly 4.5 times higher than the unmodified anode. The removal efficiency of COD and ammonia reached 82.1 % and 95.8 % respectively, both improved compared with the control and chemical modification. The modified anode effectively enriched the electrogenic Sulfurovum and Lactobacillus and thus led to a significant improvement in the electrochemical performance of SMFC. This study demonstrates the successful application of SMFCs with GO modified anodes in the in-situ removing pollutants and SMFCs present obvious remediation potential on the contaminated mariculture inhabitant.

Impact of sulfamethoxazole and organic supplementation on mixotrophic denitrification process: Nitrate removal efficiency and the response of functional microbiota.

Recirculating aquaculture systems (RAS) effluent is characterized by low COD to total inorganic nitrogen ratio (C/N), excessive nitrate, and the presence of traces of antibiotics. Hence, it urgently needs to be treated before recycling or discharging. In this study, four denitrification bioreactors at increasing C/N ratios (0, 0.7, 2, and 5) were started up to treat mariculture wastewater under the sulfamethoxazole (SMX) stress, during which the bioreactors performance and the shift of mixotrophic microbial communities were explored. The result showed that during the SMX exposure, organic supplementation enhanced nitrate and thiosulfate removal, and eliminated nitrite accumulation. The denitrification rate was accelerated by increasing C/N from 0 to 2, while it declined at C/N of 5. The decline was ascribed to which SMX reduced the relative abundance of denitrifiers, but improved the capability of dissimilatory nitrogen reduction to ammonia (DNRA) and sulfide production. The direct evidence was the relative abundance of sulfidogenic populations, such as Desulfuromusa, Desulfurocapsa, and Desulfobacter increased under the SMX stress. Moreover, high SMX (1.5 mg L-1) caused the obvious accumulation of ammonia at C/N of 5 due to the high concentration of sulfide (3.54 ± 1.08 mM) and the enhanced DNRA process. This study concluded that the mixotrophic denitrification process with the C/N of 0.7 presented the best performance in nitrate and sulfur removal and indicated the maximum resistance to SMX.

Insight in degradation of tetracycline in mariculture wastewater by ultraviolet/persulfate advanced oxidation process.

The direct discharge of trace amounts of antibiotics in mariculture wastewater results in adverse effect on the ecological environment of receiving waters. Hence, the degradation of tetracycline (TC) in mariculture wastewater by the ultraviolet/peroxydisulfate (UV/PS) process was investigated in this study. The results revealed that 95.73% removal of TC with 5 mg/L dosage was achieved after 30 min UV/PS treatment. Chloride ion (Cl-) in mariculture wastewater slightly inhibited TC degradation by scavenging free radicals. Comparably, bromine ion (Br-) significantly enhanced the removal of TC and even doubled the degradation rate. Reactive bromine species (RBS) made a major contribution to the TC removal, followed by free chlorine and other reactive chlorine species (RCS). The TC degradation pathway revealed that functional group shedding and ring-opening reactions occurred successively. In addition, TC mineralization rate was low within 30 min, causing the inefficient reduction of acute toxicity of TC and its intermediates, which could be improved by optimizing the process parameters. These results indicated that UV/PS is a new alternative process for the harmless treatment of mariculture wastewater containing the antibiotics.

Effect of sulfamethoxazole on nitrate removal by simultaneous heterotrophic aerobic denitrification.

The increase in mariculture activities worldwide has not only led to a rise of nitrogen compounds in the ecosystem but has also intensified the accumulation of antibiotics in both terrestrial and marine environments. This study focused on the effect of typical antibiotics, specifically sulfamethoxazole (SMX) on nitrate removal from mariculture wastewater by aerobic denitrification process; an aerobic denitrification system feeding with 148.2 mg/L COD, 8.59 mg/L nitrate, 0.72 mg/L nitrite, and 4.75 mg/L ammonium was set up. The hydraulic retention time (HRT) was 8 h. As the aerobic bioreactor started up successfully without SMX dosage, an excellent removal of ammonium, nitrite, and nitrate was achieved at 91.35%, 93.33%, and 88.51%, respectively; the corresponding effluent concentrations were 0.41 mg/L, 0.048 mg/L, and 0.96 mg/L. At the influent SMX doses of 0, 1, 5, and 10 mg/L, the COD removal reached 96.91%, 96.27%, 88.69%, and 85.89%, resulting in effluent concentrations of 4.53, 5.45, 17.38, and 20.6 mg/L, respectively. Nitrification was not inhibited by SMX dosage. However, aerobic denitrification was inhibited by 10 mg/L SMX. Proteobacteria was the most abundant phylum, and surprisingly its abundance increased with the increase in SMX concentration. An excellent SMX degradation was noted at initial SMX dosages of 1, 5, and 10 mg/L; the removal rate was 100%,100%, and 99.8%, respectively. The SMX degrading genera Comamonas sp., Acinetobacter sp., and Thauera sp. are of great validity to wastewater engineers because they have demonstrated efficiency in simultaneous heterotrophic aerobic denitrification and antibiotic degradation as well as COD removal. PRACTITIONER POINTS: Nitrification was not inhibited by increase in SMX dosage. An increase in SMX dosage inhibited aerobic denitrification. COD removal was not affected by increased SMX dosage. Comamonas, Acinetobacter, and Thauera had high efficiency in COD removal and SMX degradation.

Sulfamethoxazole removal from mariculture wastewater in moving bed biofilm reactor and insight into the changes of antibiotic and resistance genes.

Antibiotics are widely dosed in mariculture sector, resulting in substantial antibiotics residues. Hence, mariculture wastewater is urgent to be treated before discharging. In this study, the anoxic/oxic moving bed biofilm reactor (A/O-MBBR) was used to treat the wastewater containing sulfamethoxazole (SMX) from mariculture, SMX removal mechanism and the variation of antibiotic-resistant genes (ARGs) were investigated. The results showed that 22%-33% of SMX was removed by the bioreactor, where a small amount of SMX was adsorbed and stored by the extracellular polymers and most of SMX (>80%) was biodegraded in the anoxic tank. Occurrence of nitrate in anoxic condition was conducive to SMX degradation. Pseudomonas, Desulfuromusa, and Methanolobus species, as well as microbial catalase contributed to the SMX biotransformation. Quantitative PCR analysis of ARGs (sul1, sul2 and int1) and mRNA (sul1, sul2) showed that SMX enriched SMX-related ARGs and enhanced the expression of corresponding genes. Most of ARGs finally were discharged with effluent. Hence, the effluent from biologically based processes treating mariculture wastewater still contained antibiotics residue and resistance genes, which should be further controlled by suitable techniques.

Control of toxic sulfide in mariculture environment by iron-coated ceramsite and immobilized sulfur oxidizing bacteria.

Hydrogen sulfide (H2S) is considered one of the serious toxic pollutants in mariculture environment. Consequently, it is necessary to develop an effective strategy to prevent the production of sulfide. In this study, we modified the ceramsite with iron (ICC) and prepared a microbial agent, i.e., the immobilized sulfur-oxidizing-bacterium on the ICC (SICC), the microbial agent was following dosed in the simulated mariculture systems to control the sulfide pollutant. Results showed that the sulfide removal capacity of the new material ICC reached to 3.42 mg S g-1 in 24 h. Comparably, the microbial agent SICC presented a stable capability in oxidizing sulfide and the sulfide removal was above 65% in test media feeding with 600 mg L-1 sulfide even after five times of recycling. The microcosm experiments conducted in the simulated mariculture systems showed that the application of the ICC together with the SICC was able to quickly remove the existing sulfide and persistently inhibit the production of sulfide, the immobilized sulfur-oxidizing-bacterium survived stably in the new environment accounting for 1.22% of total microbial community. Therefore, dosing the ICC and SICC simultaneously might be a preferable strategy and presented a promising perspective in remediating the deteriorated mariculture environment.

[Enrichment of Antibiotic Resistant Bacteria and Antibiotic Resistance Genes by Sulfamethoxazole in the Biological Treatment System of Mariculture Wastewater].

Although antibiotics are heavily used in mariculture, only a small portion of the added antibiotics is absorbed. Little is known about the response process of antibiotics, antibiotic resistant bacteria, and antibiotic resistance genes to antibiotic-containing wastewater entering a wastewater treatment system. In this study, an anoxic/aerobic moving bed biofilm reactor (A/O-MBBR) was used to treat marine aquaculture wastewater containing sulfamethoxazole (SMX). The antibiotics and resistance genes in the reactor were then evaluated under selective SMX pressure, and the changing abundance patterns and the response of microbial communities and cultivable resistant bacterial populations were further explored. The results show that with an influent SMX concentration of 500 µg ·L-1 and a hydraulic retention time of 8 h, SMX had a slight effect on the removal rate of NH4+-N and NO2--N, following which the performance gradually recovered. During this stage, SMX removal reached approximately 32%, with more than 78% of SMX removed from the hypoxic zone. The resistance gene was more significantly enriched in the hypoxic zone than in the aerobic zone. In the hypoxic zone, the absolute abundance of gene sul1 increased by 2.43 log, whereas that of gene sul2 increased by 1.71 log. In the region, the absolute abundance of sul1 increased by 1.17 log, whereas that of sul2 increased by 0.91 log. Resistant plate culture and high-throughput sequencing showed that the genus Pseudoalteromonas was the most dominant culturable resistant bacteria in the reactor. The genus Pseudomonas predominated in the uncultured resistant bacteria in the reactor. This study showed that marine aquaculture wastewater containing SMX promotes the enrichment of resistance genes, causing the abundance of some resistant bacteria to increase significantly.

[Effect of Rate of Salinity Increase on the Performance and Microbial Community Structure of Sequencing Batch Reactors].

In this study, three sequence batch reactors were selected to evaluate the effects of salt-tolerant activated sludge acclimation. The effect of salinity increase rate on pollutant removal, physicochemical characteristics of activated sludge, and microbial community were investigated. The results showed that a rapid salinity increase to 30‰ (within 30 d) reduced removal efficiencies of COD and NH4+-N from 85.5% and 98.5% (18 d) to 72.2% and 81.7% (51 d), respectively. In comparison, a slower salinity increases to 30‰ (within 90 d) had a minor effect on COD and NH4+-N removal. During the rapid salinity increase, a stable shortcut nitrification occurred under 20‰ salinity, in which the effluent NO2--N reached 11.13 mg·L-1 and NO3--N decreased to 0.56 mg·L-1. When salinity increased to 30‰, the nitrite accumulation rate was about 90%, and the removal efficiency of total nitrogen increased to approximately 75%. The contents of polysaccharide and protein in extracellular polymer substances increased as salinity increased, and the polysaccharide content increased significantly when the salinity was higher than 15‰. High-throughput sequencing results illustrated that microbial diversity reduced as salinity increased, following the Shannon index decrease from 8.06 (0‰ salinity) to 4.34 (rapid salinity increase) and 6.17 (slower salinity increase). As salinity increased, Micropruina, Denitromonas, TM7a, and Marinicella exhibited good salt tolerance. The relative abundance of Denitratisoma, Defluviimonas, Arenimonas, and Denitromonas decreased more significantly following the rapid salinity increase compared with that after the slower salinity increase.

Capability of Penicillium oxalicum y2 to release phosphate from different insoluble phosphorus sources and soil.

Due to insufficient amount of soluble phosphate and poor persistence of traditional chemical phosphate fertilizers in agricultural soils, the eco-friendly and sustainable phosphorus sources for crops are urgently required. The efficient phosphate-releasing fungal strain designated y2 was isolated and identified by the internal transcribed spacer of rDNA as Penicillium oxalicum y2. When lecithin, Ca3(PO4)2, or ground phosphate rock were separately used as sole phosphorus source, different phosphate-releasing modes were observed. The strain y2 was able to release as high as 2090 mg/L soluble phosphate within 12 days of incubation with Ca3(PO4)2 as sole phosphorus source. In the culture solution, high concentration of oxalic, citric, and malic acids and high phosphatase activity were detected. The organic acids contributed to solubilizing inorganic phosphate sources, while phosphatase was in charge of the mineralization of organic phosphorus lecithin. Afterwards, the fungus culture was applied to the soil with rape growing. During 50 days of incubation, the soil's available phosphate concentration increased by three times compared with the control, the dry weight of rape increased by 78.73%, and the root length increased by 38.79%. The results illustrated that P. oxalicum y2 possessed both abilities of solubilizing inorganic phosphorus and mineralizing organic phosphorus, which have great potential application in providing biofertilizer for modern agriculture.

Transcriptomics of Planococcus kocurii O516 reveals the degrading metabolism of sulfamethoxazole in marine aquaculture wastewater.

Environmental threat induced by residual antibiotics in marine aquaculture wastewater is an urgent problem to be solved. In this study, one sulfamethoxazole (SMX)-degrading bacterium, Planococcus kocurii O516 was isolated from high SMX marine aquafarm. The isolate was able to consume more than 60% of SMX with the initial concentration of 10 mg L-1 within 72 h. Transcriptome analysis found great gene expression differences in the strains with or without SMX dosage. Three putatively differentially expressed proteins, namely AbrB/MazE/SpoVT family DNA-binding domain-containing protein, pantoate-beta-alanine ligase and MerR family transcriptional regulator, were annotated in detail. They were inferred to trigger the strain's response to SMX stress. Reverse transcription-quantitative PCR (RT-qPCR) analysis of four significantly different expressed genes accorded well with expression changes revealed by transcriptomics and confirmed the validity of transcriptome analysis. According to functional annotations of the proteins obtained by transcriptome sequencing and structural analysis of the intermediate metabolites by GC-MS, a possible SMX degradation pathway was reasonably proposed. SMX was first decomposed into sulfonamide and 5-methylisoxazole. The sulfonamide was then hydroxylated to form 4-(hydroxyamino) benzenesulfonamide. Subsequently, the sulfamic acid was detached, and 4-(hydroxyamino) phenol was formed. Finally, 4-aminophenol was generated from dehydroxylated of 4-(hydroxyamino) phenol. In sum, transcriptome analysis of the P. kocurii in response to SMX stress benefits to revealing the degradation pathway of SMX and will provide theoretical feasibility for the application of microbial method to treat the SMX-contaminated aquaculture wastewater.

[Performance and Membrane Fouling Properties in an Anaerobic Membrane Bioreactor for Salty Wastewater].

In the research, an anaerobic membrane bioreactor (AnMBR) was used to treat simulated salty organic wastewater, and the effect of salinity on reactor performance and membrane fouling properties was investigated. The results indicated that when the influent salinity increased gradually but was lower than 9.1 g·L-1, the reactor ran stably and the effluent performance was good. When the salinity increased to 10 g·L-1, the COD removal-efficiency, gas production, and methane content decreased significantly; meanwhile, the sludge concentration, sludge volume index (SVI), soluble microbial products (SMP), and extracellular polymeric substance (EPS) levels became elevated at first and then declined with the rising salinity. The system developed compact flocs and a high settling ability. The hollow fiber membrane module was run for three cycles in 118 d. The membrane operating cycle was extended from 31 d to 48 d with the increasing salinity, which favored the control of membrane fouling. SEM-EDX analysis results revealed that there were similar crystalline substances in the film membrane foulants, and Na, Mg, Al, Si, Cl, K, Ca, and Fe were the main inorganic elements. Excitation emission matrix (EEM) analysis results demonstrated that proteins and humic acids were the main components of the organic membrane foulants.

Two-stage pretreatment of excess sludge for electricity generation in microbial fuel cell.

Thermophiles hydrolysis and acidogens fermentation were sequentially adopted to pretreat excess sludge for microbial fuel cell (MFC) electricity production. The results indicated that MFC fed with the thermophiles-acidogens pretreated sludge (MFC AB), reached a higher removal of ammonia nitrogen than the MFC fed with the heating hydrolysis and acidogens fermentation pretreated sludge (MFC NB). However, compared with the MFC AB, MFC NB presented a better performance for removal of soluble chemical oxygen demand (SCOD) (90.08%) and protein (82.42%). As for the electricity production, MFC NB obtained higher voltage of 0.632 V and maximum power density with 1.05 W/m3 while MFC AB reached maximum voltage of 0.373 V and maximum power density of 0.58 W/m3. Bacterial 16S rRNA-based molecular microbial techniques showed that microbial communities on both MFC anode biofilms was diverse and different. The cooperation of fermentation bacteria and electricigen Shewanella baltica in the MFC NB may have contributed towards the improvement of electricity generation.

[Isolation and Nitrogen Removal Characteristics of Salt-tolerant Heterotrophic Nitrification and Aerobic Denitrification Bacteria Zobellella sp. B307].

A heterotrophic nitrification and aerobic denitrification strain, B307, was isolated from the sediment of Jiaozhou Bay. The strain was identified by 16S rRNA sequence analysis, and its optimization condition and salt-tolerance characteristics were studied by single factor experiment. The denitrification effect in single or mixed nitrogen sources was investigated under optimum conditions. The results allowed the strain to be identified as Zobellella sp., based on 16S rRNA sequence analysis. The best carbon source was sodium succinate, and the optimum C/N was 5, the optimal initial pH was 9, and the optimal temperature was 35-40℃ respectively. After 12 hours, the NH4+-N and the NO3--N removal efficiencies were 98.35% and 99.75% in a mixed nitrogen source system. The removal efficiencies for NH4+-N and NO3--N were 97.67% and 94.39% within 24 hours when salinity was 75 g·L-1. The strain has highly efficient heterotrophic nitrification-aerobic denitrification ability and strong salt tolerance, which demonstrated that the strain has potential for extensive application for nitrogen removal in high salt wastewater.

Microbiological aspects of thermophile pretreatment of activated sludge inhibiting electricity generation of microbial fuel cell.

Thermophile pretreatment of activated sludge greatly improves the biodegradability of sludge, but whether the pretreated products are suitable for the electricity generation of microbial fuel cells (MFCs) is still little known. In this study, municipal activated sludge pretreated by a thermophilic bacterium and heating, respectively, was separately fed into the MFCs. The performance of MFCs was examined and changes of anodic microbial communities were investigated with scanning electron microscopy and 16S rRNA gene high-throughput sequencing on the Illumina Miseq platform. The results showed that MFCs fed with heating-pretreated sludge performed preferably and the power density reached 0.91-2.86 W/m3. MFC anodes were covered with considerable Geobacter spp. However, the bioaugmentation of sludge with the thermophile was not able to support a high potential output although the pretreatment significantly increased the soluble chemical oxygen demand. The maximum power density approached 0.20 W/m3 even when the anolyte was regularly changed. It was observed that amending pH did not improve the performance of MFC. Investigation on this anodic microbial community found that the relative abundance of Lactobacillus spp. exceeded 91%. Consequently, the thermophile-pretreated products stimulated the growth of non-exoelectrogens and finally the niches of anodic biofilm were completely occupied by Lactobacillus spp.

[Effect of Silver Nanoparticles on Denitrification and Functional Gene Abundances of Sediment in Dagu River Estuary and Northwest of Jiaozhou Bay].

The influence of silver nanoparticles (AgNPs) on the denitrification performance, enzyme activity, and functional gene relative abundances of sediment was investigated based on the methods of laboratory simulation incubation in the Dagu River estuary and bay area in the northwest of Jiaozhou Bay. The different dosages of AgNPs (i.e., 0, 135, and 1350 mg·L-1 in final concentration) was added to the incubation system containing surface sediments and in-situ bottom water. During six days' incubation, the concentrations of NO3- and NO2-, NO3-, and NO2- reductases activity, and relative abundances of narG and nirS genes were measured to explore the effects of AgNPs on denitrification and its mechanism. The results showed that AgNPs significantly inhibited NO3- and NO2- reductive capacity, NO3- and NO2- reductase activity, and narG and nirS gene relative abundances, which led to aggravated accumulation of NO2-. The inhibition of NO2- reductase was significantly greater than that of NO3- reductase, and the inhibition of the nirS gene was significantly higher than that of the narG gene. The inhibition of NO3- reduction was mainly ascribed to the inhibition of functional genes, but the inhibition of NO2- reduction was mainly due to the inhibition of reductase activity. The inhibition of NO3- and NO2- reductive capacity, NO3- reductase activity, and narG and nirS gene relative abundances in the northwest of Jiaozhou Bay was significantly higher than that in the Dagu River estuary.

Effect of Substrate Conversion on Performance of Microbial Fuel Cells and Anodic Microbial Communities.

Performance of microbial fuel cells (MFCs) was monitored during the influent nutrient change from lactate to glucose/acetate/propionate and then to lactate. Meanwhile, anodic microbial communities were characterized by culture-independent molecular biotechnologies. Results showed MFC performance recovered rapidly when the lactate was replaced by one of its metabolic intermediates acetate, while it needed a longer time to recover if lactate substrate was converted to glucose/propionate or acetate to lactate. Secondary lactate feed enhanced the enrichment of bacterial populations dominating in first lactate feed. Electricity-producing bacteria, Geobacter spp., and beneficial helpers, Anaeromusa spp. and Pseudomonas spp., revived from a low abundance as lactate secondary supply, but microbial communities were hard to achieve former profiles in structure and composition. Hence, microbial community profiles tended to recover when outside environmental condition were restored. Different substrates selected unique functional microbial populations.

Effect of gradual-increasing aeration mode in an aerobic tank on nutrients' removal and functional microbial communities.

Different aeration rates and modes in an aerobic tank of an anaerobic/anoxic/aerobic (A2O) process were investigated to reveal their influence on nitrogen and phosphorus removal efficiency. Meanwhile, Illumina high-throughput sequencing of partial 16S rRNA gene of bacteria was conducted to monitor the abundance and composition of microbial communities. The results showed that higher aeration rate led to better nutrients' removal efficiency. The gradual-increasing aeration mode along the wastewater stream enhanced the contaminants' removal and the system achieved chemical oxygen demand, [Formula: see text]-N, total nitrogen (TN) removal rates of 72%, 96% and 51%, respectively. However, the gradual-decreasing or uniform aeration modes resulted in inefficient removal of TN, especially the ammonia due to low DO in the end parts of A2O. Microbial community analysis indicated that denitrifying phosphorus-accumulating bacteria Acinetobacter spp. were the most dominant groups under the gradual-increasing aeration mode in all tanks of the A2O bioreactor. Moreover, the members of genera Clostridium, Thauera and Dechloromonas also largely existed in the system. The gradual-increasing aeration mode and cooperation of different groups of bacteria made the system stable and high-performance.

Characteristics of two novel cold- and salt-tolerant ammonia-oxidizing bacteria from Liaohe Estuarine Wetland.

To achieve a better contaminant removal efficiency in a low-temperature and high-salt environment, two novel strains of cold- and salt-tolerant ammonia-oxidizing bacteria (AOB), i.e., Ochrobactrum sp. (HXN-1) and Aquamicrobium sp. (HXN-2), were isolated from the surface sediment of Liaohe Estuarine Wetland (LEW), China. The optimization of initial ammonia nitrogen concentration, pH, carbon-nitrogen ratio, and petroleum hydrocarbons (PHCs) to improve the ammonia-oxidation capacity of the two bacterial strains was studied. Both bacterial strains showed a high ammonia nitrogen removal rate of over 80% under a high salinity of 10‰. Even at a temperature as low as 15°C, HXN-1 and HXN-2 could achieve an ammonia nitrogen removal rate of 53% and 62%, respectively. The cold- and salt-tolerant AOB in this study demonstrated a high potential for ammonia nitrogen removal from LEW.